1.配页
1. Distribution page
配页即将折好的书帖从中间一帖依次套叠在一起，后把封面覆套在上面。
The book posts whose pages are about to be folded are stacked together one by one from the middle, and then the cover is covered on it.
采用骑马订装订的书籍，厚度不宜过厚，否则铁丝无法穿透，页数多只能100页。因此，采用骑马订装订的书籍一般需添页的贮帖组不会超过8组。添页到贮帖斗里时，应尽量将一摞书页整理整齐，让书页之间能进入空气，避免因堆积时间久或静电原因引起下页时粘连，进而影响开机速度。
For books bound by horse riding, the thickness should not be too thick, otherwise the iron wire cannot penetrate, and the number of pages is more than 100. Therefore, the book bound by horse riding binding generally needs no more than 8 groups of storage posts. When adding pages to the storage bucket, try to tidy up a pile of pages so that air can enter between the pages to avoid adhesion on the next page due to long stacking time or static electricity, which will affect the startup speed.
另外，对于前工序码台不平的书页，应该在续添书页时，将书页整理平齐，以免在生产过程中造成停机现象，影响生产速度和产量。有时由于天气干燥等原因，书页之间会产生静电，此时需在书页周围洒些水或者用加湿器进行加湿处理，解除静电干扰。续添封面时要注意有无倒头、白页、双张等问题。
In addition, for the uneven pages of the code table in the previous process, the pages should be sorted and leveled when adding pages, so as not to cause shutdown in the production process and affect the production speed and output. Sometimes due to dry weather and other reasons, static electricity will be generated between the pages. At this time, it is necessary to sprinkle some water around the pages or humidify with a humidifier to remove the static interference. When adding the cover, pay attention to whether there are inverted, white pages, double sheets, etc.
2.订书
2. Book ordering
订书过程中，根据纸张的厚度和材质，铁丝直径一般为0.2～0.7mm，订位为两钉钉锯外订眼距书芯上下各1/4处，允许误差在±3.0mm内。订书时要求无坏钉、漏钉及重钉;书册整齐、干净;订脚平整、牢固;订距均匀并在折缝线上;书帖歪斜误差≤2.0mm。订书过程中要经常检查所订书册是否符合标准要求，发现问题后应及时停机处理。
In the process of stapling, according to the thickness and material of the paper, the diameter of the iron wire is generally 0.2 ~ 0.7mm, and the positioning is two nail saw. The outer fixing eye is 1 / 4 from the top and bottom of the book block, and the allowable error is within ± 3.0mm. No broken nails, missing nails and heavy nails are required when stapling; The books are neat and clean; The binding foot shall be flat and firm; Set the distance evenly and on the crease line; The deviation error of the book is ≤ 2.0mm. In the process of book ordering, it is necessary to regularly check whether the book ordered meets the standard requirements, and stop the machine in time after finding problems.

3.裁切
3. Cutting
裁切时，应根据书籍尺寸大小和厚度，及时更换刀条，保证裁切出的书籍无出血、无刀花、无连页、无严重破口，成品裁切歪斜误差≤1.5mm。
During cutting, the knife strip shall be replaced in time according to the size and thickness of the book to ensure that the cut book has no bleeding, knife flower, page connection and serious breach, and the cutting skew error of the finished product is ≤ 1.5mm.
4.打包
4. Packing
打包前应检查成品质量，要求全书光洁整齐，无明显八字皱褶、死折、残页、脏迹等现象;页码顺序正确，以页码中心点为准，向里或向外误差≤0.5mm。收书码台上，要将书整理整齐，然后用堆积机打包成书，要求计数准确后再进行打包、粘贴标签。
The quality of finished products shall be checked before packaging. The whole book shall be clean and tidy without obvious eight character folds, dead folds, residual pages, dirty marks, etc; The page number sequence is correct, subject to the center point of the page number, and the inward or outward error is ≤ 0.5mm. On the book receiving code table, the books shall be neatly sorted, and then packed into books with a stacker. It is required to pack and paste labels after accurate counting.
以上的精彩内容来自：济南书刊杂志印刷更多的精彩内容来自：https://www.sdhzyw.com欢迎大家与我们进行交流。
The above wonderful content comes from Jinan leaflet printing, and more wonderful content comes from: https://www.sdhzyw.com Welcome to communicate with us.